HIGH PERFORMANCE PROTECTION FOR YOUR INDUSTRIAL AND COMMERCIAL
CONCRETE FLOORS, HARDENING & DENSIFING OF ALL CONCRETE
INFRASTRUCTURES, INCLUDING BRIDGES, ROADS, PARKING FACILITIES, RUNWAYS,
LOADING RAMPS AND MORE.
CHEMTEC ONE, a concrete
sealer, is a MULTI-COMPONENT STATE OF THE ART process used
for superior concrete
protection, that is, a proprietary blend of reactive
silicates plus surface active agents, which penetrates into the
concrete and reacts with the free calcium and lime to
form an insoluble by-product that closes the porosity, increases the
mass, strengthens, hardens and seals the concrete,
makes it much more durable and resistant to damage by chemicals and
mechanical abrasion.
The process is non-toxic, non-hazardous, non-flammable. There are no
special handling requirements under environmental regulations and
contains ZERO% VOC content.
CHEMTEC ONE concrete sealer is designed primarily
to protect, harden,
dustproof, seal, increase the mass
the durability and abrasion resistance of your high strength steel
troweled concrete
floors and also bridge
decks, loading ramps,
driveways, runways, fueling
stations, tank farms and to increase the
useful life of all concrete infrastructures. Do not
use on porous concrete blocks or other porous material where their are
actual holes in the material.
Upon application the CHEMTEC ONE sealer
penetrates into the concrete forming a solid
by-product in the gel pours, decreasing the porosity and increasing
the mass of the concrete thereby increasing the surface hardness and
strength. The process stops solids and liquids from penetrating into
the concrete, but does allow air molecules to flow
freely through the concrete and thus allowing the
concrete to "breathe".
THE BASIC BENEFITS:
CHEMTEC ONE is a MULTI-COMPONENT STATE OF THE ART PROCESS that
produces the following results in two application on brushed finished
air entrained concrete and usually just one
application on steel troweled non-air entrained surfaces, by just
spraying it on the concrete and letting it dry.(see
application instruction methods for all surfaces, especially floors,
before using) Steel troweled concrete floors will
normally develop a sheen over time.
CURING OF NEW CONCRETE:
The process is extremely effective in stopping moisture loss in
fresh concrete by applying the process to the
concrete as soon as possible after the finish
troweling operation (as soon as the concrete is firm and dry enough to
walk on with out marking), saturating the surface with the product. The
product immediately reacts with the free lime and calcium, produces a
by-product that closes up the pours there by trapping the moisture in
the concrete and greatly slowing the rate of evaporation. CHEMTEC ONE
sealer can be used as a curing agent and
surface hardener on most concrete
surfaces. This product is effective at stopping moisture loss
in fresh concrete, but does not meet ASTM C-309. DO
NOT APPLY TO WET CONCRETE:
HARDENING, DUST PROOFING AND SEALING OF CONCRETE:
Unlike some other concrete
sealers the CHEMTEC process actually produces a chemical
reaction that creates an insoluble by-product that encapsulates the
calcium component of the concrete. It increases the mass and surface
hardness of the treated concrete thereby making it much more resistant
to wear and damage. Because of this chemical reaction the pours of the
concrete are filled with this by-product and the porosity of the
concrete is greatly reduced, not allowing liquids or solids into the
concrete thereby sealing out the contaminates and
keeping the pH high.
USES:
A unique state of the art product designed for use on dense high
strength new and existing steel troweled commercial concrete
floors. Our concrete floor
sealer is primarily used for inside buildings where the
objective is to densify, harden, dust proof and seal the floors.
CHEMTEC ONE can be used to harden,
densify, seal and increase the mass
of any concrete infrastructure, such as airport runways and
taxiway's, parking facilities,
bridges, roads, loading
ramps, fueling areas and many other uses.
CHEMTEC ONE sealer is designed to deeply penetrate and
protect outside concrete infrastructures and is installed after the
concrete is fully cured. CHEMTEC ONE is the only reactive silicate
product in the world that meets both the Illinois & Ohio DOT's
specification for use on bridge structures and
decks.
TEMPERATURE LIMITS:
Applications in temperatures up to 95º F and as low as
38º F. Concrete must not be allowed to freeze
for 24 hours after application. DO NOT ALLOW THIS PRODUCT TO FREEZE. DO
NOT APPLY TO WET CONCRETE SURFACES.
SURFACE PREPARATION:
Freshly poured concrete: NONE
Existing concrete: Clean all surfaces so that they are water
permeable. Strip off coatings, sealers, paint or anything else that
would prevent the CHEMTEC process from penetrating into the concrete.
DO NOT ACID WASH CONCRETE. The concrete must be completely dry before
you apply the application.
COVERAGE:
On steel troweled industrial floors the anticipated coverage is
approximately 175 to 250 square feet per gallon, and on brushed finish
concrete anticipated coverage is 100 to 125 square feet per gallon for
each application. Actual coverage will depend on the porosity and
temperature of the concrete being treated. It takes
two applications to properly protect your porous
concrete, and generally only one application on steel troweled
surfaces.
MIXING REQUIREMENTS:
NONE: CHEMTEC ONE comes pre-mixed and ready to use.
COLOR / CLEAN UP METHOD:
Clear / Clean up with soap and water immediately after use. CAUTION:
Leaving residue in spraying equipment may damage equipment.
DRYING TIME:
4 hours. Surface may be used as soon as it is completely dry. Do not
get surface wet for 12 hours. If used as a curing medium observe normal
loads for new concrete.
CURING TIME:
CHEMTEC ONE starts curing immediately and reaches it full cure in
about 75 days. Surface can be used as soon as it is completely
dry.
APPLICATION METHOD:
Apply by spraying on the surface, saturating the surface. Keep
material from puddling, if necessary by spreading it around bristle
brooms. Areas that puddle should be brushed over to dryer areas, areas
that dry prematurely should have more material pushed to it or be
re-sprayed . After the material has been on the steel troweled
floor for 35 to 45 minutes then squeegee off the
surface. On brushed finished surfaces, just let it dry(see installation
instructions for details ).
CAUTION! DO NOT ALLOW AREAS TO PUDDLE AND DRY, AS THEY WILL LEAVE A
HARD WHITE CRYSTAL ON THE SURFACE WHEN DRY ON STEEL TROWELED
SURFACES.
STORAGE LIFE:
Up to 24 months. Do not allow product to freeze or be stored in
temperatures above
120 º F or below 38º F. Agitate barrel if stored for periods
over 3 months
CAUTION: DO NOT store in aluminum containers or use spraying
equipment with aluminum fittings. Product may react with the aluminum
to create flammable hydrogen gas. See MSDS sheet. DO NOT spray or
splash on glass, painted surfaces or decorative fronts as product may
stain these surfaces. If you do splash the product on these surfaces
wipe off with fresh water immediately. Make sure you have adequate
ventilation. Dispose of waste properly per federal, state or local
environmental regulations if required.
TECHNICAL DATA AND INSTALLATION INSTRUCTIONS:
For complete information please see the Material Safety Data Sheet "MSDS" the Technical Data Sheet, and
the CHEMTEC ONE installation
procedure for all specific surfaces, available in the documents
section.
LIMITED WARRANTY:
CHEMTEC INT'L will warrant our products to be of good quality and
that a properly prepared and structurally sound concrete surface
treated with CHEMTEC ONE formulation in accordance with the
manufactures directions by an approved applicator will remain dust
proof, hardened and protected for a minimum period of five to twenty
years (depending on structure type & use). If after the specific
treating period the surface does not remain dust proof, hardened and
protected from penetration by liquids. CHEMTEC INT'L will supply at its
own expense sufficient CHEMTEC ONE to retreat the defective surface.
This warranty does not apply if the CHEMTEC ONE is improperly applied
or if structural faults occur due to poor workmanship, improper design,
failure of other materials used in the project. The CHEMTEC ONE formula
must be used before the end of the 24 month shelf life expires.
Satisfactory results depend not only upon quality products but also
upon many factors beyond our control. Therefore except for such
replacement CHEMTEC INT'L MAKES NO WARRANTY OR GUARANTEE EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY, RESPECTING ITS PRODUCTS, and CHEMTEC INT'L shall have
no other liabilities with respect thereto. Any claim regarding product
defect must be received in witting within 90 days of the date of defect
during the warranty period. User shall determine the suitability of the
products for the intended use and assume all risks and liability in
connection therewith. All sales are final.
SYNOPSIS OF LAB TEST:
ASTM C-672 / 666 NO SCALING / see airport report
Cycles 100 with calcium chloride solution
Absorption Less than 1% after 48 hours / Less than 2% after 50
days.
AASHTO T 259 Modified Crack sealing capability Per-ODOT Spec. 841
Passed.
Chloride Absorption Specimen#1= 0.081% Specimen #2=0.056%
Dry Time
To Touch 4 hrs
Dry Hard 12 hrs
Color Clear
Specific Gravity (H20 = 1) 1.04
VOC, grams / liter 0
pounds / gallon 0
Abrasion Resistance Treated vs Non-Treated Specimen ASTM C-779
Continuous rotating grinding disk under pressure for 60 minuets.
Abrasion Resistance Increase @ 30 minutes 45% wear in. 0.044 vs
0.080
Also see Airport and Safety-Kleen private test reports
CHEMTEC ONE
Manufactured by
CHEMTEC INT'L
Cincinnati Ohio
(Member CSI)
"THE ULTIMATE CONCRETE PROTECTION"
lud07/07
|
