ChemTec ONE, a concrete sealer, is a MULTI-COMPONENT STATE OF THE ART process used for superior concrete protection, that is, a proprietary blend of reactive silicates plus surface active agents, which penetrates into the concrete and reacts with the free calcium and lime to form an insoluble by-product that closes the porosity, increases the mass, strengthens, hardens and seals the concrete, makes it much more durable and resistant to damage by chemicals and mechanical abrasion. The process is non-toxic, non-hazardous, non-flammable. There are no special handling requirements under environmental regulations and contains ZERO% VOC content.
CHEMTEC ONE concrete sealer is designed primarily to protect, harden, dustproof, seal, increase the mass the durability and abrasion resistance of your high strength steel troweled concrete floors and also bridge decks, loading ramps, driveways,runways, fueling stations, tank farms and to increase the useful life of all concrete infrastructures. Do not use on porous concrete blocks or other porous material where their are actual holes in the material.
Upon application the CHEMTEC ONE sealer penetrates into the concrete forming a solid by-product in the gel pours, decreasing the porosity and increasing the mass of the concrete thereby increasing the surface hardness and strength. The process stops solids and liquids from penetrating into the concrete, but does allow air molecules to flow freely through the concrete and thus allowing the concrete to "breathe".
CHEMTEC ONE is a MULTI-COMPONENT STATE OF THE ART PROCESS that produces the following results in two applications on brushed finished air entrained concrete, and usually just one application on steel troweled non-air entrained surfaces, by just spraying it on the concrete and letting it dry. (see application instruction methods for all surfaces, especially floors, before using) Steel troweled concrete floors will normally develop a sheen over time.
The process is extremely effective in stopping moisture loss in fresh concrete by applying the process to the concrete as soon as possible after the finish troweling operation (as soon as the concrete is firm and dry enough to walk on with out marking), saturating the surface with the product.
The product immediately reacts with the free lime and calcium, produces a by-product that closes up the pours there by trapping the moisture in the concrete and greatly slowing the rate of evaporation. CHEMTEC ONE sealer can be used as a curing agent and surface hardener on most concrete surfaces. This product is effective at stopping moisture loss in fresh concrete, but does not meet ASTM C-309. DO NOT APPLY TO WET CONCRETE:
Unlike some other concrete sealers the CHEMTEC process actually produces a chemical reaction that creates an insoluble by-product that encapsulates the calcium component of the concrete. It increases the mass and surface hardness of the treated concrete thereby making it much more resistant to wear and damage. Because of this chemical reaction the pours of the concrete are filled with this by-product and the porosity of the concrete is greatly reduced, not allowing liquids or solids into the concrete, thereby sealing out the contaminates and keeping the pH high.
A unique state of the art product designed for use on dense high strength new and existing steel troweled commercial concrete floors. Our concrete floor sealer is primarily used for inside buildings where the objective is to densify, harden, dust proof and seal the floors.
CHEMTEC ONE can be used to harden, densify, seal and increase the mass of any concrete infrastructure, such as airport runways and taxiway's, parking facilities, bridges, roads, loading ramps, fueling areas and many other uses. CHEMTEC ONE sealer is designed to deeply penetrate and protect outside concrete infrastructures and is installed after the concrete is fully cured.
CHEMTEC ONE is the only reactive silicate product in the world that meets both the Illinois & Ohio DOT's specification for use on bridge structures and decks.
Applications in temperatures up to 95º F and as low as 38º F. Concrete must not be allowed to freeze for 24 hours after application.
DO NOT ALLOW THIS PRODUCT TO FREEZE. DO NOT APPLY TO WET CONCRETE SURFACES.
Freshly poured concrete: NONE
Existing concrete: Clean all surfaces so that they are water permeable. Strip off coatings, sealers, paint or anything else that would prevent the CHEMTEC process from penetrating into the concrete. DO NOT ACID WASH CONCRETE. The concrete must be completely dry before you apply the application.
On steel troweled industrial floors the anticipated coverage is approximately 175 to 250 square feet per gallon, and on brushed finish concrete anticipated coverage is 100 to 125 square feet per gallon for each application. Actual coverage will depend on the porosity and temperature of the concrete being treated. It takes two applications to properly protect your porous concrete, and generally only one application on steel troweled surfaces.
NONE: CHEMTEC ONE comes pre-mixed and ready to use.
Clear / Clean up with soap and water immediately after use.
CAUTION: Leaving residue in spraying equipment may damage equipment.
4 hours
Surface may be used as soon as it is completely dry. Do not get surface wet for 12 hours. If used as a curing medium observe normal loads for new concrete.
CHEMTEC ONE starts curing immediately and reaches it full cure in about 75 days.
Surface can be used as soon as it is completely dry.
Apply by spraying on the surface, saturating the surface. Keep material from puddling, if necessary by spreading it around bristle brooms. Areas that puddle should be brushed over to dryer areas, areas that dry prematurely should have more material pushed to it or be re-sprayed . After the material has been on the steel troweled floor for 35 to 45 minutes then squeegee off the surface. On brushed finished surfaces, just let it dry.
(see installation instructions for details ).
CAUTION! DO NOT ALLOW AREAS TO PUDDLE AND DRY, AS THEY WILL LEAVE A HARD WHITE CRYSTAL ON THE SURFACE WHEN DRY ON STEEL TROWELED SURFACES.
Up to 24 months. Do not allow product to freeze or be stored in temperatures above 120 º F or below 38º F. Agitate barrel if stored for periods over 3 months
CAUTION: DO NOT store in aluminum containers or use spraying equipment with aluminum fittings. Product may react with the aluminum to create flammable hydrogen gas. See MSDS sheet. DO NOT spray or splash on glass, painted surfaces or decorative fronts as product may stain these surfaces. If you do splash the product on these surfaces wipe off with fresh water immediately. Make sure you have adequate ventilation. Dispose of waste properly per federal, state or local environmental regulations if required.
For complete information please see the Material Safety Data Sheet "MSDS" the Technical Data Sheet, and the CHEMTEC ONE installation procedure for all specific surfaces, available in the documents section.
CHEMTEC INT'L will warrant our products to be of good quality and that a properly prepared and structurally sound concrete surface treated with CHEMTEC ONE formulation in accordance with the manufactures directions by an approved applicator will remain dust proof, hardened and protected for a minimum period of five to twenty years (depending on structure type & use).
If after the specific treating period the surface does not remain dust proof, hardened and protected from penetration by liquids. CHEMTEC INT'L will supply at its own expense sufficient CHEMTEC ONE to retreat the defective surface.
This warranty does not apply if the CHEMTEC ONE is improperly applied or if structural faults occur due to poor workmanship, improper design, failure of other materials used in the project. The CHEMTEC ONE formula must be used before the end of the 24 month shelf life expires.
Satisfactory results depend not only upon quality products but also upon many factors beyond our control. Therefore except for such replacement CHEMTEC INT'L MAKES NO WARRANTY OR GUARANTEE EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, RESPECTING ITS PRODUCTS, and CHEMTEC INT'L shall have no other liabilities with respect thereto.
Any claim regarding product defect must be received in writing within 90 days of the date of defect during the warranty period. Petrographic analysis must accompany the claim showing that the concrete was structurally sound and met specifications including air entrainment quantities and spacing. Water cement ratios and slump of the concrete was correct. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith.
All sales are final.
ASTM C-672 / 666 NO SCALING / see airport report
Cycles 100 with calcium chloride solution
Absorption Less than 1% after 48 hours / Less than 2% after 50 days.
AASHTO T 259 Modified Crack sealing capability Per-ODOT Spec. 841 Passed.
Chloride Absorption Specimen#1= 0.081% Specimen #2=0.056%
Dry Time
To Touch 4 hrs
Dry Hard 12 hrs
Color Clear
Specific Gravity (H20 = 1) 1.04
VOC, grams / liter 0
pounds / gallon 0
Abrasion Resistance Treated vs Non-Treated Specimen ASTM C-779
Continuous rotating grinding disk under pressure for 60 minuets.
Abrasion Resistance Increase @ 30 minutes 45% wear in. 0.044 vs 0.080
Also see Airport and Safety-Kleen private test reports
CHEMTEC ONE
Manufactured by
CHEMTEC INT'L
Cincinnati Ohio
(Member CSI)
"THE ULTIMATE CONCRETE PROTECTION"
lud07/07